Tire Manufacturing Components

SMC believes that worker safety and increased productivity go hand-in-hand. It is not mutually exclusive. You can have both. Through efficient design, you can reduce risk and increase productivity at the same time. SMC has developed a variety of safety related components that can be used in a safe pneumatic system.

SMC has improved product performance and reliability with the redesigned SY series valve.  The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone resistance has been improved.   Side, top and bottom port/pipe directions are available to allow flexible installation.  The SY is available in body ported or base mounted styles, and can be used individually or manifold mounted.

The VQC series has five standard wiring packages bringing a world of ease to wiring and maintenance work, while the protective enclosures of three of them conform to IP67 standards for protection from dust and moisture. The use of multi-pin connectors to replace wiring inside manifold blocks provides flexibility when adding stations or changing manifold configuration. The VQC series has outstanding response times and long life.

• Compact and large flow capacity, VQC4000: maximum CV: 2.0
• Extensive range of fieldbus protocols available
• Power saving power comsumption: 0.4 W (Low wattage type)
• Long service life: 100 mllion cycles (According to SMC life test conditions)
• Enslosure IP67 compliant

SMC's airline equipment provides unsurpassed sensing, air regulators and air filtration performance for your pneumatic system. With our large range of pneumatic preparation products, we can provide the clean dry air  necessary to achieve the peak performance required by your fluid power system. Our connectors simplify the plumbing of all your components. SMC's innovative one-touch and uni-thread one touch fitting technology  provides dramatic time savings during the installation of both air fittings and pneumatic flow controls. We offer many variations and sizes to suit any application. Tubing is made in several sizes and packaged  in a variety of lengths.

Vacuum generator units, vacuum cups, vacuum buffers, vacuum sensor switches, fittings and vacuum instrumentation solutions allow the broadest utilization of technology and performance to meet your design  specifications. Most options are modular allowing you to add only those that are relevant to your application. SMC vacuum cups are available in many different materials, sizes and shapes, and include options  like stroke buffers to ensure that a perfect fit is made for each application. The diverse performance characteristics of SMC vacuum products allow utilization in a wide array of applications from manufacturing,  packaging, assembly, to material handling. Precision combined with performance and a full line of accessories offers a comprehensive engineering solution to meet your specific need.

Intrinsically safe SY valve is designed to be used in hazardous location by limiting the energy that could cause ignition when used with properly sized barriers.

Standard design and dimensions make the media valve series a simple replacement valve. SMC's direct operated 2-port solenoid valves have improved durability and double their service life due to the unique  construction. Built-in wave rectifier results in a quiet operating series of valves that is suitable for a wide variety of applications.

Dust collector reverse pulse jet valves are the filter cleaning components for baghouses (dust collection systems) for preventing dust explosions by removing particulates from the air.  The JSXFA dust collector valve is engineered with a robust elastomer diaphragm that requires no spring to shift, enhancing its service life to 10 million plus cycles while producing faster response times and energy savings.

The JSXFA diaphragm valve will open and close rapidly to create a short, intense blast of air with sonic shock wave to dislodge accumulated dust from bag filters and cartridge filters without disrupting regular operations.

The JSXFA can be actuated by either solenoid or air operated pilot valves, available with enclosures.

Series KFG2 fittings can operate with ambient operating fluid temperatures of -65 to 260ºC (swivel elbow type -5 to 150ºC).  With their stainless steel 316 construction and unique non-rubber seal insert connection, these grease-free fittings offer high levels of corrosion resistance, and can be used with numerous piping materials including FEP, PFS, soft and regular nylon, polyurethane and polyoelfin.  Available in male elbow, male connector, male branch tee, straight union, union tee, bulkhead union, union elbow, swivel elbow and female connector options, the KFG2 fittings can accommodate tube sizes from 4mm to 16mm and 1/8" to 1/2" with port sized thread connections from R1/8 to R1/2 and 1/8NPT to 1/2NPT.

Series TIL high purity fluoropolymer tubing is available as standard in inch sizes of 50' and 100' rolls. The TIL series has outstanding corrosion resistance, compatible with chemicals such as acids, bases and ultrapure water. The TIL series is also compatible with maximum fluid temperatures of up to 200°C

Series TL high purity fluoropolymer tubing is available as standard in metric sizes of 10m or 20m rolls. The TL series has outstanding corrosion resistance, compatible with chemicals such as acids, bases and ultrapure water.

Large Bore standard double acting, single rod version of the CQ2 compact cylinder. The CQ2 is available in bore sizes from 125mm to 200mm. It comes standard with male or female piston rod threads. It is possible to mount auto switches on any of the 4 surfaces..

• Compact, double acting, single rod, large bore
• Bore size (mm): 125,  140, 160, 180, 200
• Standard stroke (mm): 10 through 300
• Port thread types:  Rc, NPT, G
• Auto switch capable

Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% (basic 125mm bore, 100mm stroke).  This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm (depending on the mounting configuration).  Air cushions are standard on both ends.  Other options include auto switches, rod boots, and Rc, NPT or G thread types.

Electric actuators offer distinct advantages over their pneumatic counterparts. Acceleration and speed are controlled and predictable. Multiple positions are possible with high precision and repeatability.  Pushing forces can be programmed. With no need for compressed air, infrastructure and energy costs are lower. LE is SMC's current line of electric actuators, designed with a focus on easy setup and operation.  Function parameters come preset, plus an "Easy Mode" setting option allows you to be operational quickly. The LE line is available in a variety of types including: sliders, rod and guided rod, slide tables,  rotary, grippers, and miniature. Accessories include actuator controllers, and gateways.

Series IDFB refrigerated air dryers feature improved ambient (113°F/45°C) and inlet (149°F/65°C) air temperatures as well as improved flow ratings over standard models.  With an improved auto drain and standard dust filter, these units will provide years of reliable service.

Pneumatic sensors with buttons and a display to set and read values from an operator's position.

The IZT bar ionizer is an industrial static control solution.  Bar ionizers generate a curtain of static eliminating ions effective for a distance up to 2000mm/6.5 ft.  The IZT's low profile is also ideal for tight clearance installations.  Compared to SMC's IZS4 bar ionizers, the power supply and control modules have been separated from the bar, resulting in a reduction in bar height.  IZT bars can be placed closer to static-carriying materials in more confined adjacent spaces.  The separate controller can be mounted in a workstation for easier access and observation during operation.  Models include the standard IZT40, the IZT41 which adds auto-balance, emitter maintenance detection, and I/O signals, and the IZT42 with low amplitude ion generation for sensitive electronics.  Extending the value of IZT, one controller can manage a maximum of 4 ionizing bars.  Needle cartridges are easily removed, without tools, for cleaning or end-of-life replacement, futher extending this ionizer's value.

Series IR Precision Regulators are designed to be compact and light weight. The maximum set pressure has been expanded from the conventional 0.7MPa to 0.8MPa. Relief flow has been increased by nearly 5 times (compared to SMC IR201, IR401). The optional bracket and pressure gauge can be mounted on either the front or back of the unit.

The ASV series of speed exhaust controller is available in two styles depending on size.  The ASV120F/220F are elbow styles that look like a standard speed controller.  The ASV310F~510 are a tee-type design with twice the flow capacity of a standard speed controller and also add flame resistance for use in welding applications.

Series CM2-Z stainless steel cylinders are compact, lightweight and offer high performance. The piston seal and rod seal design provides excellent life. Transparent auto switch bracket provides visibility of the status of the switch. The CM2-Z series delivers extra flexibility including the option of male and female rods. Where space is at a premium, you can select a female rod end (up to 29 mm shorter) and/or boss-cut type (up to 16 mm shorter). Rubber bumpers are standard. The CM2-Z series offers a variety of mounting options.

Grippers with angular finger opening from 30° to -10° make the MHC2 suitable for workpieces of odd shapes and where space is too tight to accommodate a parallel type gripper.

Series AN silencers offer various styles and low back pressure in a compact, easy mounting design. The noise reduction has been improved to 30 dB(A) and the case is UL94-V0 grade, flame resistant material. Series AN is available with M, R or NPT threads.

Accumulated static electricity causes problems in the manufacturing environment.  Plastic wrap, foam packing, or labels cling and attract dust and dirt, causing misapplication or contamination.  Excess static  charge damages sensitive electronic components.  Even comfort and safety of personnel can be compromised.

Electric actuators offer distinct advantages over their pneumatic counterparts. Acceleration and speed are controlled and predictable. Multiple positions are possible with high precision and repeatability.  Pushing forces can be programmed. With no need for compressed air, infrastructure and energy costs are lower. LE is SMC's current line of electric actuators, designed with a focus on easy setup and operation.  Function parameters come preset, plus an "Easy Mode" setting option allows you to be operational quickly. The LE line is available in a variety of types including: sliders, rod and guided rod, slide tables,  rotary, grippers, and miniature. Accessories include actuator controllers, and gateways.

Large Bore standard double acting, single rod version of the CQ2 compact cylinder. The CQ2 is available in bore sizes from 125mm to 200mm. It comes standard with male or female piston rod threads. It is possible to mount auto switches on any of the 4 surfaces..

• Compact, double acting, single rod, large bore
• Bore size (mm): 125,  140, 160, 180, 200
• Standard stroke (mm): 10 through 300
• Port thread types:  Rc, NPT, G
• Auto switch capable

Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% (basic 125mm bore, 100mm stroke).  This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm (depending on the mounting configuration).  Air cushions are standard on both ends.  Other options include auto switches, rod boots, and Rc, NPT or G thread types.

To further compliment an abundant line of air preparation and connector equipment, SMC offers a selection of electronic sensors including digital pressure switches, vacuum switches, and flow switches.

To further compliment an abundant line of air preparation and connector equipment, SMC offers a selection of electronic sensors including digital pressure switches, vacuum switches, and flow switches.

Large Bore standard double acting, single rod version of the CQ2 compact cylinder. The CQ2 is available in bore sizes from 125mm to 200mm. It comes standard with male or female piston rod threads. It is possible to mount auto switches on any of the 4 surfaces..

• Compact, double acting, single rod, large bore
• Bore size (mm): 125,  140, 160, 180, 200
• Standard stroke (mm): 10 through 300
• Port thread types:  Rc, NPT, G
• Auto switch capable

Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% (basic 125mm bore, 100mm stroke).  This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm (depending on the mounting configuration).  Air cushions are standard on both ends.  Other options include auto switches, rod boots, and Rc, NPT or G thread types.

Electric actuators offer distinct advantages over their pneumatic counterparts. Acceleration and speed are controlled and predictable. Multiple positions are possible with high precision and repeatability.  Pushing forces can be programmed. With no need for compressed air, infrastructure and energy costs are lower. LE is SMC's current line of electric actuators, designed with a focus on easy setup and operation.  Function parameters come preset, plus an "Easy Mode" setting option allows you to be operational quickly. The LE line is available in a variety of types including: sliders, rod and guided rod, slide tables,  rotary, grippers, and miniature. Accessories include actuator controllers, and gateways.

To further compliment an abundant line of air preparation and connector equipment, SMC offers a selection of electronic sensors including digital pressure switches, vacuum switches, and flow switches.

Large Bore standard double acting, single rod version of the CQ2 compact cylinder. The CQ2 is available in bore sizes from 125mm to 200mm. It comes standard with male or female piston rod threads. It is possible to mount auto switches on any of the 4 surfaces..

• Compact, double acting, single rod, large bore
• Bore size (mm): 125,  140, 160, 180, 200
• Standard stroke (mm): 10 through 300
• Port thread types:  Rc, NPT, G
• Auto switch capable

Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% (basic 125mm bore, 100mm stroke).  This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm (depending on the mounting configuration).  Air cushions are standard on both ends.  Other options include auto switches, rod boots, and Rc, NPT or G thread types.

Pneumatic products need special lubricant, seal material and design considerations to withstand elevated temperature applications. SMC offers solutions that deliver performance in the extreme temperatures as high as 150°C.

Electric actuators offer distinct advantages over their pneumatic counterparts. Acceleration and speed are controlled and predictable. Multiple positions are possible with high precision and repeatability.  Pushing forces can be programmed. With no need for compressed air, infrastructure and energy costs are lower. LE is SMC's current line of electric actuators, designed with a focus on easy setup and operation.  Function parameters come preset, plus an "Easy Mode" setting option allows you to be operational quickly. The LE line is available in a variety of types including: sliders, rod and guided rod, slide tables,  rotary, grippers, and miniature. Accessories include actuator controllers, and gateways.

Large Bore standard double acting, single rod version of the CQ2 compact cylinder. The CQ2 is available in bore sizes from 125mm to 200mm. It comes standard with male or female piston rod threads. It is possible to mount auto switches on any of the 4 surfaces..

• Compact, double acting, single rod, large bore
• Bore size (mm): 125,  140, 160, 180, 200
• Standard stroke (mm): 10 through 300
• Port thread types:  Rc, NPT, G
• Auto switch capable

Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% (basic 125mm bore, 100mm stroke).  This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm (depending on the mounting configuration).  Air cushions are standard on both ends.  Other options include auto switches, rod boots, and Rc, NPT or G thread types.

To further compliment an abundant line of air preparation and connector equipment, SMC offers a selection of electronic sensors including digital pressure switches, vacuum switches, and flow switches.