IMTS

HRS, HRS-R, HRSE compact recirculating chillers are designed to meet the widest range of single-point applications in both industrial and technology settings. The package design is robust enough for the factory, yet ergonomic and compact for lab installations. Coolant can be either heated or cooled within the set temperature range. Choose from eight cooling capacities, air or water cooled refrigerant, and global power supply options.

Large Capacity chillers offer a cooling capacity range of 10 to 28 kW. Coolant and refrigeration circuits are included in a compact and lightweight package. Extracted heat can be air or water cooled. An inverter provides demand-based rotation control for the compressor, pump and fan (air cooled model), offering substantial energy savings.  Electric options ensure global power supply compatibility.

With the release of the KN series nozzles and gauge heads 30~90% of air consumption required for the current nozzle operation can be saved with the appropriate selection of the new nozzle and sizing. Many variations of nozzle are available with tube materials including nylon, soft nylon, soft copper pipe and OST tubing. Sizes range from 4mm-20mm.

Series SGC coolant valve, with both CE and RoHS accreditation, provides the perfect solution for high speed machining. Due to the SGC’s unique scraper, squeeze seal, grease channel and dry bearing construction, the valve’s service life will exceed 5 million cycles. The introduction of a built-in magnet allows auto switches to be fitted, enabling confirmation of whether the valve is open or closed.

A low maintenance filter, series FN1 eliminates the need for element replacement. SMC's unique element construction is composed of a series of grooved filter plates and wave washers placed one above the other. When compressed, the gaps between the filter plates and wave washers filter foreign matter. When decompressed, the element widens the gap between the filter plates and wave washers, allowing dust and foreign particles caught between the plates to be washed away. The gaps between the filter plates are equally maintained by the wave washers to allow stable back-flush operation.

Actuator stroke position sensor is an analog output over the entire length of the stroke.  The D-MP is available in 4 measurement ranges.  Unit is IO-Link compatible.

This next generation ISE70 pressure sensor provides continuous quantitative values, as well as switched digital outputs when pressure set points are met.  This sensor is also IO-Link compatible.  Sensor information, such as identity, functional state, cable connection, and current or switch values can be set or monitored remotely though an IO-Link master, and connected to a fieldbus network.  The ISE70 is designed for abusive environments that may also include splashed coolant, lubricants or grime.  Electronics are packaged in a metal housing, while the piping connection is a stout lug with female threads, which together protect the sensor against accidental collisions with other objects in the area.  A smooth display face with membrane type buttons avoids contamination from grit and sticky residue that could clog or jam raised rubber buttons.  The display is angled and can rotate 336 degrees, to permit easy reading when indirectly mounted.  The main screen shows instantaneous values in red or green, while the sub screen setting appear in orange.  Switch indicators will also light when set points are reached.

ISE20B-L is a digital pressure sensor supporting the IO-Link communication protocol.  When paired with an IO-Link master, measured values, and settings can be accessed from the HMI screen of a PLC.  ISE20B-L incorporates IO-Link 16-bit process data includes 2 output bits for set points, a diagnosis bit, and 13 bits for the measured pressure valve.   The 3-screen, 3-color display shows the instantaneous reading in red or green, and the setting label and its numerical value in orange.  ISE20B-L is UL/CSA, CE and RoHS compliant, with an IP65 enclosure rating.

ZSE20B(F)-L is a digital vacuum sensor with IO-Link communication protocol support.  When paired with an IO-Link master, measured values, and settings can be accessed from the HMI screen of a PLC.  ZSE20B(F)-L incorporates IO-Link 16-bit process data includes 2 output bits for set points, a diagnosis bit, and 13 bits for the measured pressure value.  The 3-screen, 3-color display shows the instantaneous reading in red or green, and the setting label and its numerical value in orange.  ZSE20B(F)-L is UL/CSA, CE and RoHS compliant, with an IP65 enclosure rating.

PF2M7 is a digital flow sensor compatible with air, nitrogen, argon or carbon dioxide.  PF2M7 refreshes the legacy PFM7 with several enhancements.  The thermal sensor is protected in a bypass flow path to reduce contact with moisture and contaminants, avoiding accuracy deterioration and damage.  Dimensions and weight have been reduced, especially beneficial when installed on moving tooling.  Finally, current consumption has been reduced by 36%.  The LCD 4-digit display can be red or green, changing when a set point is reached.  Options include cable connector type, a manual flow adjustment valve, and panel or bracket mounts.  Push to connect fittings or threaded ports align the fluid supply line in a straight configuration, or from the rear/bottom.  Output options include two switch signals, one switch with an analog signal, or IO-Link.  PF2M7 is IP40 rated, and meets RoHS and CE standards.

Series PF3W7-L digital flow sensor constantly monitors water or coolant flow.  "L" models are IO-Link compatible.  These sensors also have the "Z" designation for redesigned piping adapters, imparting a 13-53% weight reduction depending on flow range.  PF3W7-L features an integrated 3-color, 2-screen display.  Options include a manual flow adjustment valve and temperature sensor.  The main screen displays instantaneous flow value in red or green, while the white subscreen can show temperature, the switch set point, accumulated or peak/bottom value, or a line name.  The display rotates in both clockwise and counter-clockwise directions, offering improved readability during operation.  When paired with an IO-Link master, values and settings can be accessed from the HMI screen.  PF3W7-L incorporates IO-Link version 1.1 and COM2 speed.  48 bits of process data include flow and temperature values, switch outputs, and diagnostics.  Both IO-Link data and switch outputs can be read over the M8 or M8-to-M12 cable.  PF3W7-L is IP65 rated, and is both RoHS and CE compliant.

PF3WS and PF3WR are remote, separated versions of the manifold.  PF3WR is the return path and includes the sensor.  The 1" main return is oriented at 90° to the flow paths, and can flow through or be closed on the opposite end.  3 flow ranges are available, with up to 10 stations on the smaller two ranges, and up to 5 stations on the largest.  Flow adjustment and stop valves are optional and will match on every station.  Sensor features are identical to the stand-alone PF3W-Z.  IO-Link compatibility is also optional.  PF3WR is IP65 rated, and CE and RoHS compliant.

PF3WS and PF3WR are remote, separated versions of the manifold.  PF3WS is the supply path and does not include a sensor.  This type is mechanical only.  The 1" main supply is oriented at 90° to the flow paths, and can flow through or be closed on the opposite end.  3 flow ranges are available, with up to 10 stations on the smaller two ranges, and up to 5 stations on the largest.  Flow adjustment and stop valves are optional, and will match on every station.  PF3WS is IP65 rated, and CE and RoHS compliant.

The ISA3-L is an IO-Link compatible version of SMC's ISA3 digital gap checker.  A gap checker uses air pressure to verify the presence and proximity of a workpiece.  Applications include confirmation of raw material placement before machining or other fabrication operations, or the correct seating of a component into a jig or fixture to trigger the next assembly sequence.  ISA3-L includes features like 2 sensors detect supply and outlet pressure, to help determine whether and where this is a clog.  NPN or PNP switch type is selectable electronically.  The sub-screen has been divided into 2 screens, to display more information or finer resolution.  The lower limit of the setting range can be extended down to zero.  IO-Link communication expands functionality.  Gap size, supply and outlet pressure are available as 16-bit integers. 6 bits and settings monitor 2 switch outputs.  2 additional bits are available for pressure and error diagnosis.  Settings can be stored by the IO-Link master to copy automatically when replacing or deploying multiples.  ISA3-L is CE and RoHS compliant, with an IP67 enclosure rating.

PSE200A is a pressure sensor monitor with an informative, easy to read 3 screen, 3 color display.  Connect up to 4 PSE series remote pressure sensors, then select a channel to view the sensor’s measured value on the main screen.  Alternately, the range input function can scale any 1-5V signal from another sensor type to a display value from -1500 to 1500.    View a variety of secondary data on the sub-screens, including switch set point value, level meter, character string for labeling and more.  Check differential pressure between CH1-CH2, or CH3-CH4.  Additional functions include anti-chatter, error codes, power saving, key lock, security code and others.  This monitor is also IO-Link compatible for viewing measured values, diagnostics and switch output status of all channels.  Internal hardware and applied pressure errors can also be indicated.  Parameters set on the monitor can be reset by the IO-Link master if a new monitor replaces a damaged or failed one.  PSE200A is CE and RoHS compliant, with an IP65 front face when panel mounted (IP40 otherwise).

EX260 series is a compact and cost effective fieldbus solution for output applicable to SMC's most popular directional control valves such as New SY, SV, VQC, and S0700 Series. It can control up to 32 solenoids in one manifold. Available protocols are EtherNet/IP™, PROFINET®, EtherCAT®, PROFIBUS DP®, DeviceNet™ and CC-Link. EX260 series has standard dual port connectivity to eliminate the need of switches or branch connector, reducing wiring and component cost. IP67 enclosure rating ensures protection against dust and washdown environment.

Series ITV electro-pneumatic and electronic vacuum regulators control air/vacuum pressure steplessly in proportion to an electric signal. The units are compact, lightweight, and include an easy to read LED display.  Input signals can be analog current or voltage, 4 or 16 point presets, or a range of communication protocols including CC-Link, DeviceNet™, PROFIBUS, RS-232C or I/O-Link.  EtherNet/IP™, and PROFINET are available as well.  See the separate configurators on this site.  Monitor output is available as an analog or switch signal.  ITV regulators are IP65 equivalent.

Membrane air dryer series IDG is available in a single unit or combination unit style. IDG/M models combine a mist separator and micro mist separator with a single unit. IDG/V models combine a regulator with the IDG/M model. Options available include one-touch fitting exhaust of purge air. If purged air is not exhausted around membrane air dryer, air is exhausted with tubing away from its dryer.

IDFB series refrigerated air dryers are cUL listed for use in North America.  These 60 Hz models have rated flows up to 459 SCFM (780 m³/hr [ANR]).

ISE20 is a digital pressure sensor with an informative, easy to read 3 screen, 3 color display.  The main screen shows the instantaneous reading in red or green, while two sub-screens can display the setting label and its numeric value in orange.  ISE20 saves energy with only 25mA current consumption.  Further, the switch output responds within 1.5ms once the set pressure value is reached.  ISE20 is UL/CSA and RoHS compliant, with an IP40 enclosure rating.

Service life can be extended by blowing the air to cool the tip after arc welding.  This unit is an energy savings valve with a 0.5W power consumption. Designed to be space saving and compact.

CH series hydraulic cylinders are available in compact, round body, JIS or tie-rod types. Nominal pressure ranges from 3.5MPa to 16MPa. Bore sizes are available, depending on the series, from 20 to 160. Auto switches are available on most models.

FH series suction filters are compact and lightweight.  Designed with an aluminum casted housing.  Element can be replaced by simply opening the cover to detach the element without touching the pipes.  The filter can be fitted with a differential pressure indicator which senses when the element is becoming dirty, facilitating maintenance and helping to avoid pump damage such as cavitations.  The FHG series suction guard was designed to prevent collected dust from falling into the tank.  Since all dust is eliminated during trial operation, it is not necessary to replace flushing oil.  Options include differential pressure indicator, differential pressure indication switch, air breezer, and cap.

FH series suction filters are compact and lightweight.  Designed with an aluminum casted housing.  Element can be replaced by simply opening the cover to detach the element without touching the pipes.  The filter can be fitted with a differential pressure indicator which senses when the element is becoming dirty, facilitating maintenance and helping to avoid pump damage such as cavitations.  The FHG series suction guard was designed to prevent collected dust from falling into the tank.  Since all dust is eliminated during trial operation, it is not necessary to replace flushing oil.  Options include differential pressure indicator, differential pressure indication switch, air breezer, and cap.

FRL Units can be assembled with a variety of combinations. Add mist separators, pressure switches, shut-off valves to any combination of Filter, Regulator, or Lubricator to optimize flow rate and filtration ratings at point-of-use compressed air systems. Meet energy savings goals and save space on the production floor with the modular design of units.

Series AFF is strongly recommended as a pre-filter for a refrigerated dryer to avoid fouling of the dryer's heat exchanger.

Series HAW is able to cool high temperature compressed air from compressors down to 40°C or less while efficiently removing moisture from the air. As the HAW is water cooled, it can be used where there is high temperature, high moisture and heavy foreign particles. A thermometer makes it easy to check outlet air temperature.

The AMG series water separator is installed on the air pressure line to remove water drops from compressed air. It is available in 7 sizes with a variety of optional combinations to meet your application requirements.

The CKG1-XC88/XC89/XC91 series is a clamp cylinder available in two styles of clevis widths (16.5mm, 19.5mm). It is a non-lube, compact, lightweight cylinder with a built-in speed controller. The CKG1 is available in 3 bore sizes with stroke lengths up to 150mm. Options include easy speed adjustments, rod attachments and auto-switch capabilities.

The CQ2 weld spatter resistant compact cylinder is an option of the world's best selling pneumatic cylinder and can be supported globally. The CQ2-XC88/XC89/XC91 is available in 6 bore sizes from 32mm to 100mm. It comes standard with male or female piston rod threads. For mounting flexibility, it is possible to mount auto switches on any of the 4 surfaces.

The MGP-XC88/XC89/XC91 is designed for high side load applications found in material handling, lifting and stopping in welding environments. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body.

Combining weld spatter resistance, compact cylinder size and rotational capability, the MK2T-XC88/XC89/XC91 cylinder is designed for heavy duty clamping applications, with an available integrated arm that swings out of the way when the cylinder is extended. 90deg. clockwise or counter clockwise rotation is available, and clamping arms with adjustment screw are standard options.

The MWB series is a tie-rod cylinder MB series with lock and is ideal for applications requiring intermediate stops, emergency stops, and drop prevention.  The MWB series is an improved design over the MNB series with its improved ease of maintenance with separate lock and cylinder construction.  The exhaust locking design allows for the lock release to be manually operated with a hexagon wrench.  The MWB series is available with many standard options including seven mounting types, port thread variations, optional rod boot, air cushion or rubber bumper cushion design, pivot bracket option and rod end bracket options.  Available in bore sizes 32, 40, 50, 63, 80, 100mm.

The CLS series cylinder with lock is ideal for applications requiring intermediate and emergency stop and drop prevention. The compact lock unit is lightweight and saves space. A switch is optional on the brake cylinder so the operating state of the lock unit (brake piston) can be detected using the switch signal. By separating the lock mechanism and the brake cylinder, SMC has minimized the influences of unlocking air quality such as moisture and condensation.

High speed or high load cylinder applications frequently require additional speed and flow control devices to control the stopping of the load. SMC's RHC series features a longer cushion design which is capable of stopping heavy or high speed loads while maintaining the simplicity of a standard air cushion cylinder. This enhanced cushion allows the kinetic distance, which results in the ability to absorb up to 23.8 ft-lb of energy and operate reliably at speeds up to 118 in/sec. Even with the improved performance of the RHC, cushion adjustment remains as simple as adjusting the cushion needle valve. 

Parallel Grippers most popular type of gripper where opposing jaws travel in parallel to hold a workpiece.

Series MHM is a magnetic gripper that can be used in place of vacuum cups or grippers when holding a metallic workpiece.  Auto switches can be mounted on 2 surfaces.  Expanded mounting options include body tapped, lateral, and central.

The VHS series provides a convenient means of isolating supplied pressure in a pneumatic system and exhausting downstream pressure for maintenance purposes.  The units can be locked in the exhaust position and can be an integral part of an energy isolation system.  Air flow direction is easily identified by handle orientation and labelling.  

Special versions of the VP and VG series valves that conform to ISO13849-1 safety standard, categories 1 to 4. They are available as dual residual pressure release safety valves with detection of main valve position.

Soft start-up valves enable a gradual initial pressurization of a system and quick exhaust by blocking the supply of air to minimize system shock.

Series VR51 is a safety valve for applications where machine operation with two hands is recommended. It conforms to EN574. The operating pressure range is .25 - 1 MPa.

The ISA3 is a unique sensor that uses air pressure to verify the presence and proximity of a workpiece.  The placement of raw materials can be confirmed before machining or other fabrication operations.  The correct seating of a component into a jig or fixture can generate a switch output to trigger the next assembly sequence.  ISA3's new display quickly and clearly summarizes workpiece status for the operator.  Establish the switch point in 3 easy steps.  Lower air consumptions, zero exhaust noise, easier wiring, and excellent anti-clogging measures round out this 3rd generation gap checking device.  ISA3 is CE and RoHS compliant, with an IP67 enclosure rating.

Liquid flow sensors with buttons and a display to set and read values from an operator's position.

Pneumatic sensors with buttons and a display to set and read values from an operator's position.

Sensors to be installed out of view, with analog outputs for a sensor monitor or the HMI.

Liquid flow sensors with buttons and a display to set and read values from an operator's position.

HRS, HRS-R, HRSE compact recirculating chillers are designed to meet the widest range of single-point applications in both industrial and technology settings. The package design is robust enough for the factory, yet ergonomic and compact for lab installations. Coolant can be either heated or cooled within the set temperature range. Choose from eight cooling capacities, air or water cooled refrigerant, and global power supply options.

The Rack Mount Chillers are a temperature control device mountable in a 19-inch rack. Rack mounting recovers desktop or floor space, permitting stacking of related devices and mobility, depending on the rack style. Recirculating fluid removes heat from the process source. The heat is then removed from the fluid by an air or water-cooled refrigeration circuit. Coolant temperature stability is ±0.1°C within a set temperature range of 10 to 35°C.

S coupler series KK employs a unique connection method. A slim body design and large effective area are achieved with a construction that does not use steel balls or valve springs and therefore does not restrict the flow path. Together with a reduction of the body size, pressing parts and resin parts are used to achieve an overall weight reduction.

Series VMG has a large effective area of 0.05in² (30mm²), without nozzle. Pressure loss is 0.725psi (0.005MPa) or less when nozzle bore size 2.5mm is used.  Piping direction is optional from the top or bottom.  Available nozzles include: male thread; high efficiency; low noise w/male thread; and extension nozzles.

Using SMC speed (flow) controls with built in one-touch fittings minimizes installation time, reduces mounting height and enables a more compact machine design. These speed controls allow the body to be rotated to facilitate simple installation. Available in thread sizes from M3 to 1/2 in both inch (NPT) and metric R(PT) and with tube sizes from 3.2mm to 12mm OD (metric) and 1/8 to 1/2 OD (inch) and with optional elbow and universal style (increased flexibility) and meter-in and meter-out, these speed controls are designed to meet most applications.

KQ2 one-touch, metric and inch size fittings are available in a wide variety of sizes, body styles and thread types. The use of a special profile seal allows the KQ2 to be used for a wide range of pressures from a low vacuum up to a pressure of 1MPa.  The KQ2 release collar releases both the chuck and collet to provide a low disconnection force for easy removal of the tubing.

Series TRTU flame resistance three-layer tubing is suitable for air and water piping in environments where sparks from arc welders, etc., may be a problem.  The three-layer design uses a flame resistant polyolefin (equivalent to UL-94 Standard V-0) for the outer area.  The TRTU series is available in a variety of colors and sizes and is RoHS compliant.

SMC has improved product performance and reliability with the redesigned SY series valve.  The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone resistance has been improved.   Side, top and bottom port/pipe directions are available to allow flexible installation.  The SY is available in body ported or base mounted styles, and can be used individually or manifold mounted.

The VQC series has five standard wiring packages bringing a world of ease to wiring and maintenance work, while the protective enclosures of three of them conform to IP67 standards for protection from dust and moisture. The use of multi-pin connectors to replace wiring inside manifold blocks provides flexibility when adding stations or changing manifold configuration. The VQC series has outstanding response times and long life.

The CQ2 weld spatter resistant compact cylinder is an option of the world's best selling pneumatic cylinder and can be supported globally. The CQ2-XC88/XC89/XC91 is available in 6 bore sizes from 32mm to 100mm. It comes standard with male or female piston rod threads. For mounting flexibility, it is possible to mount auto switches on any of the 4 surfaces.

The MGP-XC88/XC89/XC91 is designed for high side load applications found in material handling, lifting and stopping in welding environments. The cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body.

Combining weld spatter resistance, compact cylinder size and rotational capability, the MK2T-XC88/XC89/XC91 cylinder is designed for heavy duty clamping applications, with an available integrated arm that swings out of the way when the cylinder is extended. 90deg. clockwise or counter clockwise rotation is available, and clamping arms with adjustment screw are standard options.

Compact and lightweight, the KQB2 one-touch fitting uses electroless nickel plated brass components as standard specification. Its maximum operating temperature is 150° C.  KQB2 fittings can be used with fluid, and in environments having a large temperature change.  Configuration variations have been improved to 17 models.  Applicable tube sizes are Ø3.2 to Ø16 and 1/8" to 1/2".  Series KQB2 is available with M, R, Rc, UNF, NPT or G connection threads.